Just How to Remove as Well as Replace a Bath Tub
Just How to Remove as Well as Replace a Bath Tub
Blog Article
We have unearthed this post involving A Step-by-Step Guide to Installing a Bathtub below on the internet and believe it made sense to discuss it with you in this article.
Setting up a bathtub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and also in some cases, tiling skills. Changing an old tub with a new one is additionally a reasonably hard job. If the old tub is conveniently easily accessible, the project can relocate rapidly; if you have to open up a wall to get rid of the old tub and also place the new tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require a helper to vacate the old tub and embeded in the new one. See to it you have certified yourself for the task and fit attempting it. Instead of hiring a specialist to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Chances are you may require an expert plumber to make tube links.
This short article will certainly help you set up a brand-new tub in your washroom if you have currently bought a new bathtub and don't require to change the plan of your previous water pipelines.
Your tools as well as product checklist ought to consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you ought to do is detach the water. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be rather troublesome due to the restricted access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this process. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the tap in place with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet adapters. The former type needs to be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Tub
Using both wood boards under its feet, place the bath tub in the needed placement. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 little points.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bath tub until the level reads degree.
To set up faucets, fit the bottom of the outermost versatile tap port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the supply of water and also check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bath tub should wait until the tub has actually been made use of at least once as this will certainly resolve it right into its final setting.
Getting ready for the Installment
Firstly, the supporting framework supplied with the bath must be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps system to avoid pressure on the bathtub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall between the bathroom and also the tiling, bring about issues with moisture as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and cartridges, and can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always fill the tub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealant can crack fairly very early if you do not take into account this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our topic on How to Install a Bathtub. Thanks a lot for taking time to read our article post. Are you aware of someone else who is sincerely interested in the topic? Please feel free to share it. Many thanks for going through it.
Go Company
Report this page